Shinear
08-27-2008, 08:14 PM
just posted to see if anyone was looking at or running d sports, from on of the buggy forums.
3 R1 motors plus some drive parts.
http://www.minibuggy.net/forum/sale/9019-fire-sale-two-yahaha-r1-motors-hub-complete-drivetrain.html
Need these out of my way. I have 2 low mileage 2003 yamaha R1 motors, both with less than 1000 miles. The motor in the car had 700 miles on it and the spare had 350 miles on it. One motor is currently in my car and can be test drove before removal. Included is EVERYTHING needed for a complete streetbike drivetrain. Trust me the motor is just the half of it in these cars as most of you know. Included is the R1 factory race harness and computer, power comander, factory gauges (the way to go so you can do onboard diagnostics with the gauges), Custom aluminium intake with K&N, aftermarket stainless header w/ muzzy slipon muffler, battery, radiator and hoses, extra factory header, extra radiator and fan, extra harness, and severial other extras. This set up is fast. I can keep up with my buddys acura V6 and I have NEVER been beat by a vw powered car.
For the rear drive hub I had a splined shaft for made by Jeff @ jeffco with moly 930 drive flanges. The hub has a flange to bolt different sprockets to (i have a few different ones) and an inboard brake rotor with willwood caliper. All hub bearings are high quality sealed bearings.
Also included will be the shifter and fabed shifter box.
After purchase I will completely remove motor w/ custom waterjetted mount, wiring harness, hub, and everything else included (I am probably forgetting a few things). I am just going to cut the back half of my car out and pull out the harness. This harness has everything bypassed such as exup valve and kickstand switch. All of this takes quite a bit of time. The harness is all labeled for easy hook up. You should only need some swiches and a fuel pump (motor already has a regulator). This is a very complete setup and will cut down a ton of time and headaches I am also willing to seperate the hub, and the motors.
$3100 for everything, in Lakeside CA.
try link if that does not work e mail me and I will get you in touch.
Mark
3 R1 motors plus some drive parts.
http://www.minibuggy.net/forum/sale/9019-fire-sale-two-yahaha-r1-motors-hub-complete-drivetrain.html
Need these out of my way. I have 2 low mileage 2003 yamaha R1 motors, both with less than 1000 miles. The motor in the car had 700 miles on it and the spare had 350 miles on it. One motor is currently in my car and can be test drove before removal. Included is EVERYTHING needed for a complete streetbike drivetrain. Trust me the motor is just the half of it in these cars as most of you know. Included is the R1 factory race harness and computer, power comander, factory gauges (the way to go so you can do onboard diagnostics with the gauges), Custom aluminium intake with K&N, aftermarket stainless header w/ muzzy slipon muffler, battery, radiator and hoses, extra factory header, extra radiator and fan, extra harness, and severial other extras. This set up is fast. I can keep up with my buddys acura V6 and I have NEVER been beat by a vw powered car.
For the rear drive hub I had a splined shaft for made by Jeff @ jeffco with moly 930 drive flanges. The hub has a flange to bolt different sprockets to (i have a few different ones) and an inboard brake rotor with willwood caliper. All hub bearings are high quality sealed bearings.
Also included will be the shifter and fabed shifter box.
After purchase I will completely remove motor w/ custom waterjetted mount, wiring harness, hub, and everything else included (I am probably forgetting a few things). I am just going to cut the back half of my car out and pull out the harness. This harness has everything bypassed such as exup valve and kickstand switch. All of this takes quite a bit of time. The harness is all labeled for easy hook up. You should only need some swiches and a fuel pump (motor already has a regulator). This is a very complete setup and will cut down a ton of time and headaches I am also willing to seperate the hub, and the motors.
$3100 for everything, in Lakeside CA.
try link if that does not work e mail me and I will get you in touch.
Mark